Share
Pin
Tweet
Send
Share
Send
Materials for work:
• Cord (for example, from an old vacuum cleaner) with a working fork at one end - 1 pc.;
• Pendant lamp holder - 1 pc.;
• Empty cylinder from mounting foam - 1 pc .;
• Chandelier body with a horn (without shade) - 1 pc.;
• Short bolt - 3 pcs.;
• Nut - 3 pcs.;
• Drill, thin drill, screwdriver.
Stages of the work:
The first stage: bring the wires.
We release the old chandelier from the ceiling.
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska.jpg)
We find the wire from unused household appliances (in the presented version, the cord from the vacuum cleaner was used). It is desirable: the wire is more authentic, with a double insulating layer, so that it has a working plug from one end.
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-2.jpg)
Unscrew the horn from the body. We pass the cord into it so that the direction of movement goes towards the connection of the horn with the ceiling.
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-3.jpg)
Second stage: connect the wires. We are looking for a cartridge hanging for the lamp.
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-4.jpg)
We disassemble it into its components: we disconnect the case and the threaded sleeve, we take out the porcelain insert.
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-5.jpg)
The cord end extended from the horn is freed from external insulation, we clean the wires themselves (by cutting and removing the inner insulation layer from both wires).
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-6.jpg)
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-7.jpg)
We hang stripped wires into the chandelier body.
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-8.jpg)
Further work is carried out inside the luster housing. First, insert the wires into the cartridge case.
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-9.jpg)
We fix it with a special nut, which fastens the horn of the chandelier to the body.
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-10.jpg)
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-11.jpg)
The next step: connecting the wires to the porcelain cartridge insert.
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-12.jpg)
To do this, twist the loop at the end of each of the wires.
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-13.jpg)
Unscrew the contact screws on the porcelain liner. We put a screw in the eyelet. We put the screw in place and fasten it tightly to the insert (the wire ring remains under the screw on the insert).
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-14.jpg)
After screwing the contact screws, we place the porcelain insert in the cartridge case (wires inside).
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-15.jpg)
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-16.jpg)
We connect the cartridge case with a threaded sleeve.
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-17.jpg)
The third stage: we make a reflector.
To concentrate the direction of light, we make a "curtain" - a reflector, cutting out a spade-shaped part from an empty cylinder of mounting foam.
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-18.jpg)
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-19.jpg)
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-20.jpg)
From one end of the reflector we drill holes with a thin drill, trying to combine them with the holes on the chandelier body - the places where the lampshade is attached to it (in the presented version of the hole there are three pieces - in the center and edges).
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-21.jpg)
We twist the reflector with the chandelier body with short bolts.
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-22.jpg)
From the inside of the chandelier body, each bolt is fixed with a suitable nut.
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-23.jpg)
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-24.jpg)
We screw the incandescent lamp into the carrier.
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-25.jpg)
![](http://img.uaft2404.org/img/sdela-2019/lampa-perenoska-26.jpg)
That's all. We check the operability of a home-made carrier and begin its immediate operation.
Share
Pin
Tweet
Send
Share
Send